GreenCalculusGet a free key
  1. Home
  2. Guides
  3. Reference
  4. What is the carbon footprint of concrete?
Last reviewed October 2026

What is the carbon footprint of concrete?

Quick Answer

About 196 kg of CO₂e per cubic metre for a typical structural mix (C30/37, the German average in the ÖKOBAUDAT database, cradle to gate), or about 150 kg per cubic yard. Weak concrete for blinding is about 112 kg/m³ and high-strength grades about 286 kg/m³. Over 90% of it comes from the cement.

Concrete is mostly sand, gravel and water, which have almost no carbon footprint. The problem is the cement that binds them: it makes up about a seventh of the mix by weight but nearly all of its emissions, because making cement releases CO₂ from the limestone itself, not just from the fuel. This page gives the footprint per cubic metre and per cubic yard for each strength class, explains where it comes from, puts cement in the global total and shows how much lower-carbon mixes save.

Per cubic metre and cubic yard, by strength

Stronger concrete needs more cement, so its footprint rises with the strength class. These are ÖKOBAUDAT’s German average ready-mix values for the production stage (modules A1–A3 of EN 15804: raw materials, transport to the plant and mixing). The cubic-yard column converts at 0.7646 m³ per cubic yard.

Ready-mix concrete, cradle to gate (A1–A3) — ÖKOBAUDAT 2024
Strength classkg CO₂e per m³kg CO₂e per yd³Typical use
C8/1011286Blinding, mass fill, non-structural
C12/1512999Kerb bedding, drainage surround
C16/20150115Strip footings, light foundations
C20/25157120House slabs, general foundations
C25/30181138Reinforced slabs and walls
C30/37196150Structural frames, ground-bearing slabs
C35/45220168Heavier structural work, car parks
C45/55273209High-strength columns, precast
C50/60275210High-strength and prestressed work
C55/67286219Specialist high-strength work

Per kilogram, that is roughly 0.05 to 0.12 kg of CO₂e, since a cubic metre weighs about 2.3 to 2.4 tonnes. That is low per kilogram, far below steel at about 2.2 kg on the global average (see the carbon footprint of steel), but concrete is used in such volumes that the total is large. These are averages for German ready-mix; a particular mix can be well above or below them, as the next sections show.

Why the cement carries the footprint

Take a standard structural mix of 340 kg of cement, 1,050 kg of gravel, 760 kg of sand and 170 kg of water per cubic metre. With UK Portland cement (CEM I) at 0.84 kg CO₂e per kg, from the Mineral Products Association’s Fact Sheet 18:

One cubic metre of a 100% Portland cement mix, A1–A3
Ingredientkg per m³kg CO₂eShare
Cement (CEM I)340285.696.8%
Gravel and sand1,8109.43.2%
Water1700.20.1%
Total2,320295.2100%

The cement is 15% of the weight and 97% of the carbon. Cement is made by heating limestone and clay to about 1,450°C to form clinker. Heating limestone (CaCO₃) splits off CO₂ whatever fuel is used; this calcination accounts for about 59% of Portland cement’s footprint (the IPCC default is 0.52 t of CO₂ per tonne of clinker, and Portland cement is about 95% clinker). Most of the rest is the fuel burned in the kiln.

Cement factors vary by country and type. ÖKOBAUDAT’s German Portland cement dataset is 0.665 kg CO₂e per kg [GreenCalculus materials.concrete.cement.cem_i_portland.module_a1_a3 · OEKOBAUDAT 2024 · v2026.299] and its blast-furnace slag cement (CEM III/A) 0.433 [GreenCalculus materials.concrete.cement.cem_iii_blast_furnace.module_a1_a3 · OEKOBAUDAT 2024], against the UK’s 0.84. Compare cements within one source: the databases mix datasets of different types.

Lower-carbon mixes

Because the carbon is in the clinker, the main lever is to use less of it. By-products such as ground granulated blast-furnace slag (GGBS) and fly ash, or a blend of calcined clay and limestone (LC3), replace part of the cement. On the MPA’s UK factors, the same 340 kg binder mix gives:

C30/37-type mix, 340 kg binder per m³, A1–A3, MPA Fact Sheet 18 factors
Binderkg CO₂e per m³Saving
100% Portland cement (CEM I)295–
30% fly ash21228%
LC3-50 (30% calcined clay, 15% limestone)19733%
50% GGBS17939%
50% GGBS, by-product allocation16544%

The two GGBS rows differ because slag is a by-product of steelmaking, and how much of the steel plant’s emissions it should carry is a choice: the MPA’s default (economic allocation) gives it 0.155 kg CO₂e per kg, the by-product view 0.075. Fly ash and GGBS supplies are also limited and falling as coal plants and blast furnaces close, which is why calcined clay is drawing attention.

Two other levers need no new materials:

  • Don’t over-specify strength. Moving from C35/45 to C30/37 where the design allows saves 24 kg CO₂e per m³ on the averages above.
  • Use the supplier’s figure. A product-specific Environmental Product Declaration (EPD) for the actual mix replaces any average, and low-carbon mixes are often only visible that way.

To try your own mix, use the concrete embodied carbon calculator.

Over the whole life of the concrete

Production is most of the story, but not all of it. ÖKOBAUDAT gives the later life-cycle modules for its C30/37 average:

C30/37 ready-mix, kg CO₂e per m³, ÖKOBAUDAT 2024
StageModulekg CO₂e per m³
ProductionA1–A3196
CO₂ reabsorbed while in use (carbonation)B1−14
DemolitionC13.32
Transport to processingC210.3
Crushing and processingC35.05
Total, production to end of lifeA–C201
Credit for reusing the crushed aggregateD−12.1

Concrete slowly reabsorbs some CO₂ from the air as it ages, which is why module B1 is negative. Module D is reported separately and is not subtracted from the total, as EN 15978 requires.

Cement in the global total

The CO₂ released by calcination in cement making was 1,473 million tonnes in 2024, according to the Global Carbon Project: 3.8% of the world’s fossil CO₂. That counts only the chemical release; the fuel burned in kilns is counted with coal, oil and gas, so higher shares quoted elsewhere usually add the fuel and sometimes the rest of the supply chain. China produced 42% of it (618 Mt) and India 13% (186 Mt). The world total was 2% higher than in 2015. For every country, see CO₂ emissions by country.

For construction as a whole, including steel, transport and site work, see the carbon footprint of construction.

Worked examples: a house slab and a patio

A 10 m × 10 m ground slab, 150 mm thick, in C25/30:

  • Volume: 10 × 10 × 0.15 = 15 m³
  • Footprint: 15 m³ × 181 kg CO₂e/m³ = 2,715 kg, about 2.7 tonnes of CO₂e

A 20 ft × 20 ft patio, 4 inches thick, in C20/25:

  • Volume: 20 × 20 × 4/12 = 133.3 ft³ = 4.94 yd³ = 3.78 m³
  • Footprint: 3.78 m³ × 157 kg CO₂e/m³ = 593 kg of CO₂e

Neither includes reinforcing steel, which is counted separately.

Why published figures disagree

  • The mix. A weak blinding mix and a high-strength one differ by a factor of two or more, and so do mixes with and without slag or fly ash.
  • The unit. Per cubic metre, per cubic yard and per tonne give very different numbers for the same concrete; check which one you are reading.
  • The boundary. Production only (A1–A3) is the usual headline. Some figures add delivery, end of life or the carbonation credit.
  • The cement. Factors for Portland cement differ between countries and databases, as shown above.
  • Cement versus concrete. Statistics about the cement industry’s share of global CO₂ describe cement, not concrete, and often include fuel.

Frequently asked questions

About 196 kg of CO₂e for a typical structural mix (C30/37) to produce, on ÖKOBAUDAT’s German averages. It ranges from about 112 kg for weak blinding concrete to 286 kg for high-strength grades, and a mix made only with Portland cement can reach about 295 kg.

About 150 kg of CO₂e (about 330 lb) for a typical structural mix, since a cubic yard is 0.765 cubic metres. Lower-strength mixes for slabs and footings are about 120 to 138 kg per cubic yard.

Because of the cement. Making cement clinker releases CO₂ from the limestone itself, about 59% of its footprint, plus the fuel needed to heat the kiln. Cement is only about a seventh of concrete by weight but about 97% of its emissions.

The chemical CO₂ from making cement was 1,473 million tonnes in 2024, 3.8% of global fossil CO₂ (Global Carbon Project). Including the fuel burned in kilns raises the share.

Roughly 157 to 220 kg of CO₂e per cubic metre for everyday mixes, cradle to gate, and about 196 kg for a typical structural grade. Using slag, fly ash or calcined clay in place of part of the cement cuts it by about 28% to 44%.

Related: concrete embodied carbon calculator · concrete and cement methodology · MPA Cement Fact Sheet 18 · ÖKOBAUDAT · embodied carbon

Scroll to Top